Shredders for Sale

May 7, 2017

Used Scrap Metal Ferrous Shredding System for Sale

Tom Stanek

An effective energy efficient metal shredding line up

Update: This unit has been sold  

5000 HP Ferrous Scrap Metal Shredding System for sale.  The heavy duty shredder box is 88 x 101 inch with 4 inch thick walls.  This is a complete package with infeed conveyor, ferrous line, motors, pumps, water injection, and coolers.  Many extras such as power systems and a computer managed over sized double feed roll allow this machine to shred serious volume in a compact package.  150 tons per hour ferrous out production.

The primary drive is a 5000 HP (3730 KW) A/C Wound Rotor Motor.  The hard charging Schorch motor keeps churning day after day.  Dual axial pole magnets, cyclone air cleaning system, and split picking station allow for extremely clean and dense ferrous scrap.

Slip Power Recovery Drive is included.  Motor rotor current is managed in a switchable duel system using either liquid rheostat or solid state SPR drive.  The SPR efficiently runs the motor with greater power, cooler temperatures, more tons per hour, while allowing less flicker and inference with local electrical grid, thus greater options for relocating the installation.  Comes with heavy duty GE transformer (25kV/4160), power factor capacitors, and many extras that take the added cost out of relocating the machine.

The system includes infeed conveyor, shredder dampening springs, under mill oscillator, conveyors, magnets, water injection system, de-dusting air cleaning zee box, dual picking station, stacking conveyor, and non-ferrous radial stacking conveyor.  Many spare casting wear parts and spare parts are available.  The motor room is protected by an air filtration system.  Roof mounted coolers, control cabin, infra red camera, and shredder management computer round out the system.  Non-ferrous separation system as NOT part of this package.

An effective and energy efficient equipment line up.  A very complete system, well cared for with low tons on the machine.   This unit represent an excellent opportunity for a new installation or if you are looking to replace an aging shredding plant.

Spare motor and rotor available as extras.

Contact us at k2.castings.com for more details.  Serious inquires only.

 

February 12, 2017

Rebuilt Hagglunds MB 283 Drive Motor Available

Tom Stanek

Many of our customers continue to run the venerable, long lasting MB series hydraulic drive motors with their shredding installations.  Infeed conveyors and double feed roll drives are commonly powered by the MB 283.

As you know, Hagglunds is now part of Bosch Rexroth and the MB series is no longer in production.  The CA series of radial piston motors is the current supply in many new shredder installations.  If you want a new motor, it will be a CA or CB series.  Replacing an older MB with a new CA requires adapters and a little conversion.

Fortunately, the well made Hagglunds units are tough.  Units can be rebuilt with new parts.  You just have to find them!   One of our shops has one.

The unit is rebuilt with new parts including a new roll pin, cyinder roll bearing, wear ring, gasket set, radial lip seal dust seal, and piston ring.  Its been tested and is backed by a 6 month shop warranty.

Why wait for new or go through a conversion?  Get this in your spares inventory.  Grab it while you can.  Contact us for details.

June 24, 2016

Double Feed Roll Drive Shaft

Tom Stanek

DFR SHAFT READY Our fine friends at PG&H Engineering have a Doubled Feed Roll (DFR) drive shaft ready in their shop for immediate delivery.  This shaft fits Metso Generation III DFR rollers using CA280 splined Hagglunds drive motors.

Click here to request more information.

INFEED SPLINED 2

January 21, 2016

Hammermill 96×104 Excess Parts Available

Tom Stanek

Excess Parts 96104  A customer has a large inventory of excess, unused wear parts for a Hammermill 96 inch by 104 inch shredder.  If you are running or rebuilding one of these workhorse machines, this is a great way to save some money.  Please contact us if you have interest in learning more.96104 Parts 2

Hammermill machines are one of the storied brands in the shredding world, both productive and reliable.  With a bolt together shredding box, they are easier to rebuild.  As time moves on,  support is not always easy to obtain from the current brand owner.

These manganese steel parts include hammers, grates, cutter bars, and pin protectors. Tie rods and end disk caps are also part of the assortment.

Hammermill 96×104 Excess Part Inventory

PART NUMBER / REFERENCE

DESCRIPTION QUANTITY
ET9903-                           21-9980 ROOF COVER BREAKER BAR 1
ET9900-                           21-9970 ROOF COVER 1  
CH-73096-A201RH         22-7000 LOWER SIDE LINER RH (22) 1
CH-73096-A201LH         22-0705 LOWER SIDE LINER LH (22) 1
CH-73096-B201RH         22-0690 LOWER SIDE LINER RH (23) 1
CH-73096-B201LH         22-0695 LOWER SIDE LINER LH (23) 1
 CH-73096-C201RH        22-0680 LOWER REAR LINER RH (24) 2
CH-73096-C201LH         22-0685 LOWER REAR LINER LH (24) 1
CH-73096-D201RH        21-2050 UPPER REAR LINER RH (25) 1
CH-73096-D201LH         21-2055 UPPER REAR LINER LH (25) 1
CH-73096-E201RH         21-9950 UPPER CENTER LINER RH (26) 1
CH-73096-E201LH         21-9960 UPPER CENTER LINER LH (26) 1
CH-73096-FlOlRH           21-9930 UPPER FRONT LINER RH (27) 1
CH-73096-FlOlLH           21-9940 UPPER FRONT LINER LH (27) 1
 DH-73096-208UA          21-9900 INNER TOP BREAKER BAR (13) 1
J-44194-                          21-8910 SOLID GRADE BAR (37) 5  
CH-7896-Al-                   21-9910 GRATE BAR (36) 10
DH-73074-A129              20-9230 LOWER BREAKER BAR (30) 2  
BH-73096-213-Al            21-9920 INTAKE BREAKER BAR (14) 2
DH-73074-A330-            21-9220 CUTTER BAR (35) 4
B-7283-1 CAP HD (54) 112+76
BH-7996-30 HAMMER 500 LBS (53) 137+76
DH-73074-C344 HAMMER PINS 16
KN-179 COMP.FLIGHT (3 CROWSERS) 25
(SB-18252) petit (16) END DISC CAP WO/POCKET 27
(SB-18253) grand (22-5605) (8) END DISC CAP W/POCKET 19
B-D449 (48) PIN END DISC CAP 40
B-B525 (48) WASHER END DISC CAP 38
101-639A PADS96″ 23
CH-73074-J-19 TIE BOLTS 126″ 11
CH-73074-J-308 TIE BOLTS 140″ 9
#22-3020 (DESSIN PDE 57715) COMBO 0
#22-0260 (DESSIN PDE 58991) FULL SOLID 0

 

96104 Parts 1

April 7, 2015

Used 98104 Auto Shredder for Sale

Tom Stanek

We have a customer with a used scrap metal auto shredder for sale.  The unit is a model 98104 Texas Shredder, 4000 HP, disk rotor, with infeed and ferrous downstream. Rated output is 100 tons per hour.

If you’re looking for a cost effective way into shredding, you found the right package. High output, solid key components, lots of extras. One of the most common shredder designs means parts are common as well.

  • System has new and overhauled parts.
  • Downstream consists of ferrous cleaning system only.
  • The Alstom 4000 HP wound rotor AC motor is in excellent condition.
  • Includes a very nice portable modular indoor substation for power distribution & receiving utility power, with a metering bay and disconnects.

u-jointsIncludes many extras needed to install and operate, typically not part of used auto shredding packages.  Contact us for details.  This system is located in the USA.

This unit processes automobiles, end of life vehicles (ELV), appliances, sheet metal, baled ferrous, and loose tin.

 

January 29, 2015

Used Infeed Conveyor Needed

Tom Stanek

We’re in search of a used infeed conveyor for an 80 to 98 inch shredder.  Complete unit welcome, but the frame and towers will do.  If you know of a unit for sale in the continental United States, please contact us.  We have a few buyers in need of an infeed.

As always, we are interested in knowing about any used scrap metal shredding equipment you might have for sale.  K2 Castings works to help our customers find what they need,  linking buyers and sellers together.

INFEED 2

February 15, 2014

Scrap Metal Shredder for Sale

Tom Stanek

European manufacturer, 2.7 x 2.2 meter (87 x 106 inches)

  • New shredder, ready for delivery with 60 days notice.  
  • Rated power 2500 to 4000 horsepower
  • 70-95 metric tons per hour ferrous output at 3000 HP (2200 KW)
  • Shreds automobiles (end of life vehicles ELV), appliances, #2 HMS, baled sheet metal

ShredderSketch

Equipment includes the following components and subsystems: 

  • Infeed conveyor system
  • Feed Chute, Shredder Box, Double Feed Roll system
  • Springs for vibration damping
  • Shredder Rotor (capped disk with bearings & housings; barrel rotor)
  • Shredder Drive Turbo Coupling system
  • Drive shaft and couplings
  • Under Mill (shredder) Oscillating (vibrating) Conveyor
  • Pin Puller System with Platform
  • Shredder Hydraulic System
  • Very Heavy Duty, Welded Plate Construction
  • Top & Bottom discharge, reject door
  • Rotor Hydraulic Lift provides clear access to bottom grates
  • Hydraulic box clamp & rotor bearing clamps
  • Rotor Brake
  • Fully capped barrel style rotor has extensive service life

Scrap Metal Shredder with Rotor Elevator
Options

  • 2nd shredder barrel rotor for spare
  • Motor purchase is an option, if a drive system is needed for short delivery

 Price:     Offered by K2 Castings on behalf of the owner, serious inquiry only

February 11, 2013

Scrap Metal Auto Shredder for Sale

Tom Stanek

98104 Texas Shredder, 4000 HP, disk rotor, infeed and downstream. 100 tons per hour output. 

If you’re looking for a cost effective way into shredding, you found the right package. High output, solid key components, lots of extras. One of the most common shredder designs means parts are common as well.

System has new and overhauled parts. New Non-ferrous separation system available separately or as part of the shredder package. 

Portable / Modular Indoor substation power distribution center & switch center to receive utility power, metering bay, and disconnects. 

Includes many extras needed to install and operate, typically not part of used shredding packages.  Call for details.

u-joints

October 8, 2011

Shredder Motor Transformer for Sale

Tom Stanek
  • 10 MVA Westinghouse Low Impedance Transformer
  • Sized  for a 4000-6000 HP shredder drive
  • 12,470 V primary to 4160 secondary, Delta Wye
  • Extras such as multiple taps, current transformers, liquid level gauge, pressure vac gauge, others.

Available for immediate installation or purchase as a backup spare.

Call for details.

May 30, 2011

Shredder Motor for Sale 4000 HP

Tom Stanek

Used 4000 HP A/C wound rotor motor for sale.  4160 Volts, 600 RPM.  Great back up drive motor in case you need a spare.  And you do need a spare!  Check it out here.